Laserworld Tarm 3 OUTDOOR

The Laserworld Tarm 3 OUTDOOR is especially designed for outdoor laser installations. It comes equipped with the top quality laser setup known from the standard tarm units, but has a waterproof enclosure that not only protects the components inside from water, but also shields off direct heat from solar exposure. A specially designed roof in front of the output window prevents it from getting impacted by direct rain. To cope with varying temperatures, the tarm OUTDOOR units are equipped with an active watercooling system, that is built into the housing. An active heating system helps to keep the laser systems operational even at low temperatures, meaning the tarm 3 OUTDOOR lasers can be used at environmental temperatures between -10°C and +45°C. A CT Scanner upgrade with LAS Turboscan drivers is available for the tarm 3 OUTDOOR to achieve top end quality graphics results.

The tarm 3 OUTDOOR show laser projector is a full color whitelight RGB laser systems with full analog color modulation and diode-only equipment. The guaranteed output power is specified at 3'000 mW after optics.

The tarm 3 OUTDOOR units have a built-in network DAC for Showcontroller, Showeditor, Touchdesigner, MadLaser, etc., but also can be controlled with any ILDA laser control software such as Pangolin Quickshow, Pangolin Beyond, LSX, Lasergraph DSP, etc. via external ILDA interface (e.g. FB3) and ILDA streaming. They also have a built-in memory with pre-set patterns, that can be easily triggered through ArtNet and automatic mode.

The tarm 3 OUTDOOR comes with integrated ShowNET network interface and free laser show software. Details in the box below.

The tarm 3 OUTDOOR laser has great beam specifications with a diameter of ca. ca. 4.5 mm and a beam divergence of less than <0.6 mrad.

It is equipped with a bright red (1'000 mW / 637 nm), a green (900 mW / 520 nm), and a blue (1'700 mW / 450 nm) diode laser source.

The scanners are very fast with 45kpps @ 8° ILDA standard and allow for a maximum scan angle of 50°. Thus they are well graphics capable and suitable for professional laser applications.

Optionally as upgrade available: CT-6210 scanners with 60 kpps@8° ILDA and a max. scan angle of 60°.

• IP65 waterproof housing
• 3'000 mW guaranteed power
• Graphics capable - 45kpps @ 8° ILDA Scanners
• Full colour mixing - analogue modulation
• Extremely sharp intense beams - low divergeance of <0.6 mrad
• Control screen (internal) for convenient mode selection
• Free computer control software - Showeditor - upgradable to Showcontroller
• Integrated powerful mainboard with advanced configuration features (geo-correction, zone setup, colour balancing, etc.) and DAC feature
• Multiple control modes - stand-alone, ArtNET, LAN and ILDA streaming

The tarm 3 OUTDOOR features an integrated ShowNET network interface with free laser control software included!

Start with your own professional laser show thanks to the intuitive Showeditor laser show software which comes with every new tarm 3 OUTDOOR for free. The Showcontroller software is supported as well and can be purchased additionally.

The integrated ShowNET allows for direct input through ILDA and LAN. It is also possible to trigger single frames via ArtNet. Custom frames and shows can be played from an integrated SD card (included in delivery) – even in stand-alone mode!

There are two different ArtNet modes:

• DJ Mode with the most used features for beginners. Only a few channels are used for a quick and easy access to the most important adjustments directly at the laser system.
• Professional Mode with all ArtNet features especially for users with an ArtNet capable console. All adjustments can be triggered and allow for full control of the professional laser show.

The integrated ShowNET works as DAC (digital to analogue converter) and enables ILDA streaming.

• Guaranteed Power at aperture: 3'000 mW
• Power Red: 1'000 mW / 637 nm
• Power Green: 900 mW / 520 nm
• Power Blue: 1'700 mW / 450 nm
• Beam Specifications: ca. 4.5 mm / <0.6 mrad
• Scanner: 45kpps @ 8° ILDA; optional: CT-6210 with LAS Turboscan: 60kpps @ 8° ILDA, max. 60°
• Max. Scan Angle: 50°
• Laser Source: Diode
• Laser Class: 4
• Operation Modes: LAN, ArtNet, ILDA Streaming, integrated SD card, stand-alone
• Basic Patterns: Over 120 (layers, tunnels, fences, waves, etc.)
• Accessories: Incl.power cable, manual, E-Stop, interlock connector, full version Showeditor software license included
• IP rating: IP65
• Power Supply: 85 V - 250 V / AC, 50/60 Hz
• Power Consumption: 300 W
• Dimensions: 800 / 370 / 260 mm
• Weigh: 22 kg